Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
This great article in the next paragraphs in relation to How to Install a Bathtub is immensely insightful. Don't skip it.
Setting up a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably hard job. If the old bathtub is readily obtainable, the job can relocate quickly; if you have to open a wall surface to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified on your own for the work as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to take into consideration using one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your bathroom if you have already bought a new bathtub and do not require to transform the setup of your previous supply of water pipes.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipes. When the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Safeguard the tap in position with the maker supplied backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former type must be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the tub until the spirit level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the supply of water and check all joints and brand-new pipework for leakages and also tighten them if essential. Load the tub and also check the overflow electrical outlet as well as the normal outlet for leaks.
Lastly, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub must wait up until the bathtub has actually been made use of a minimum of once as this will settle it right into its last position.
Preparing for the Installation
To start with, the supporting structure provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a rigid seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to issues with wetness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog post about Tools You Need to Install a New Bathtub when doing a lookup on the search engines. Are you aware of another person who is in the market for the topic? Be sure share it. Thank you for your time. Visit again soon.
Expertise? One call away. Report this page